CAMERA CONTROL
From camera-side control on CineView M7 series to wireless operation with Accsoon SEE App, key camera controls stay right where you need them.
Choose direct control on the monitor, wireless control through the Accsoon SEE App, or a combined workflow that fits your on-set camera rig.
Explore CompatibilityCOMPATIBLE PRODUCTS
Use the monitor's Camera Control interface with wired USB-PTP or supported IP control methods.
Connect a supported camera to CineView SE 4K or Master 4K Lite and operate it from a phone or tablet.
Combine wireless video monitoring and remote camera operation in a single on-set workflow.
CineView M7/M7H Pro
Camera control is built into the CineView M7 series monitoring workflow. From the Camera Control interface, operators can adjust ISO, Shutter Speed, Aperture, White Balance Preset and Custom WB Kelvin parameter controls, plus additional Focus Control and Record Trigger with optional Record Status Sync.
Camera control works in Monitor Mode and TX Mode. TX Mode supports USB wired control only. RX Mode does not support camera control.
Focus Control is unavailable due to camera limitations.
Set the camera’s physical WB toggle to “PRE” for accurate white balance control.
CONNECTION GUIDE
USB-C
Connect the camera's HDMI or SDI output to the monitor's HDMI input.
Connect the camera to the monitor with a USB-C data cable.
Open Camera Control on the monitor. Once connected, the supported camera controls become available.
NETWORK
Connect the monitor to the camera's Wi‑Fi network, or connect both devices to the same local network.
Enable network control on the camera and note its IP address.
Confirm that the camera and monitor are on the same network.
Set the monitor to Monitor Mode.
Open Camera Control and select IP Control.
Enter the camera's IP address, then connect.
Once connected, use the available controls to adjust exposure, control focus, and start or stop recording.
SE 4K · MASTER 4K LITE
With a compatible camera connected to CineView SE 4K or CineView Master 4K Lite, Accsoon SEE App brings ISO, shutter speed, aperture, touch focus, and bi-directional record control to your phone or tablet.
HOW TO
Connect the camera to the transmitter: HDMI or SDI for video, and USB-C for camera control.
Connect your phone or tablet to the transmitter’s Wi‑Fi, then open the latest Accsoon SEE App to access camera controls.
To record simultaneously on the camera and in the Accsoon SEE App, enable synchronized recording under Record/Stream.
COMBINED WORKFLOW
Pair a CineView M7 series monitor with a supported CineView transmitter for wireless monitoring and camera control through Accsoon SEE App—all on one screen.
Connect the camera to the transmitter: HDMI or SDI for video, and USB-C for camera control.
Set the CineView M7 Pro or M7H Pro to Monitor Mode to avoid a Wi‑Fi conflict, then install the latest Accsoon SEE App.
Connect the CineView CineView M7 Pro or M7H Pro monitor to the transmitter’s Wi‑Fi.
Open Accsoon SEE App to view the live feed and access the available camera controls.
See which cameras are supported by CineView M7/M7H Pro and Accsoon SEE App. Available controls vary by camera and connection method.
Direct camera control on the monitor
Please note that focus control is not available for the Nikon Z5, Z50, Z6, Z6 II, and Z7 II due to camera limitations.
Camera control via CineView SE 4K or CineView Master 4K Lite
Camera control is available only when a mobile device connects to the transmitter via Wi‑Fi, not available through RX USB connection.
The listed camera models have been validated internally. Other models may work, but compatibility is not guaranteed.
FAQ
Please make sure HDMI Info Display is turned off. Then, check whether Half-Press Shutter Button is enabled in Camera Control. If it is, disable it and try again.
Set the camera to M mode or another mode that allows manual aperture adjustment.
This may be caused by the camera's USB settings. Please check whether USB Power Delivery is turned off.
Make sure the lens is set to Autofocus (AF) mode and set AF Area to Small Zone in the camera settings.
